HAPPYMODEL Mobula6 ELRS 1S 2.4ghz 65mm Brushless FPV whoop drone

Write Review
Additional Information
  • Weight : 0.15
  • Model : MOB6ELR2S
Qty :
Update log:
Mobula6 ELRS 2.4Ghz version comes with Updated ELRSF4 2G4 V3.1 flight controller since 25th Feb
V3.1 Version flight controller Updated
MPU6000 changed to ICM20689 because of MPU6000 discontinued
Onboard VTX changed to OPENVTX support 0mw~400mw
Pre-install Betaflight firmware which support ELRS V2.0 TX firmware

ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable. Now we are about to release Mobula6 equipped with ExpressLRS RC link system, the new Mobula6 elrs would coming out with a new 0702 brushless motor, that would be the lightest brushless motors all over the world. We’re sure this would be a good option for you in the Tiny Whoop Season.

AIO Flight controller with ELRS Receiver and 5.8G VTX
Super light 1S 65mm Brushless whoop only 18.7g
Equipment with the lightest brushless motors-SE0702 only 1.46gram
Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible for 1S Lipo/LIHV

Brand Name: Happymodel
Item Name: Mobula6 ELRS 1S 65mm Brushless whoop drone BNF version
Wheelbase: 65mm
Size: 80mm*80mm*37mm
Weight: 18.7g

2.4GHz ExpressLRS SPI receiver

Mobula6 ELRS 2.4G
Flight controller ELRS F4 2G4
Firmware target CRAZYBEEF4SX1280
Built-in ExpressLRS receiver
Built-in Dshot ESC 5A
Receiver antenna plug SMD ceramic antenna
Onboard VTX power 25mw~200mw
Brushless Motor 0702 KV26000
Propeller HQPROP 31mm Bi-blade
Battery 1s 300mah Lipo battery

Package includes:
Mobula6 1S 65mm whoop Drone Frame x 1
ELRS F4 2G4 flight controller built-in SPI expresslrs 2.4G receiver x 1
SE0702 KV26000 brushless motor x 4
HQPROP 31mm bi-blade propellers(4cw+4ccw) x 1
Runcam Nano3 1/3 CMOS 800TVL camera x 1
Onboard 5.8G 25mw~200mw VTX x 1
1S 300mah 30C LiHV Battery x 4
1S Lipo/LIHV USB Charger x 1
Propeller disassemble tool x 1

Spare parts specifications:
Mode: SE0702 KV26000
Stator Diamter:7mm
Stator Length:2mm
Shaft Diameter:?1mm
Motor Dimension(Dia.*Len):?9.5mm*14mm
No.of Cells(Lipo):1S only

Center Thickness:5mm
Prop Disk Diameter:31mm
Center Hole Inner diameter:1.0mm

Flight controller
ELRS F4 2G4 flight controller V3.1 built-in SPI expresslrs 2.4G receiver MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in ExpressLRS 2.4G receiver
Built-in 5V 1A BEC
Built-in voltage detection

Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600

Onboard SPI ExpressLRS 2.4GHz Receiver
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna : SMD antenna
Telemetry output Power: <12dBmReceiver protocol: SPI ExpressLRS
Could bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module ExpressLRS version 1.0.0 or 1.0.1 both compatible

Onboard 5.8g VTX
Output power: 25mw~200mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race bandSmartaudio ready

Runcam Nano3
Model: RunCam Nano 3
Image Sensor: 1/3? CMOS
Horizontal Resolution: 800TVL
Lens : 2.1mm(M8) FOV 160°
Signal System: PAL/NTSC Non Switchable
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power:DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm

Lipo Battery
Continuous Discharge Rate: 30C
Size: 57mmx12mmx7mm
Weight: 8gConnector: PH2.0

There are currently no product reviews.

Write Review

There are currently no videos

also purchased

We Accept

Shopping Cart[more]

0 items