Introducing the Moblite7 Ultralight FPV Brushless Whoop! Made in collaboration with FPV pilot "Mr Shutterbug," this whoop is one of the lightest 75mm drone in the market! The Moblite7 features the RunCam Nano3, Onboard SPI Frsky D8 Receiver, DiamondF4 FR FC, 5A BLheli_S 4-in-1 ESC, 5.8GHz VTX, and more! This mini and lightweight whoop (75mm) will take you to hard-to-get places!
Features
The lightest 1s 75mm brushless whoop
Powerful and efficiency
The lightest 1s AIO 5IN1 F4 flight controller
New Unibell EX0802 brushless motors
VTX power switchable 25mw~200mw
Low profile Canopy design
Specifications
Brand Name: Happymodel
Item Name: Moblite7 1S 75mm ultra-light brushless whoop
Wheelbase: 75mm
Size: 97mm*97mm*25mm
Weight: 19.5g (without battery)
Weight:36g(with Original 1s 650mah Lipo battery )
Motor
Mode: EX0802 19000KV
Configu-ration:9N12P
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:?1mm
Motor Dimension(Dia.*Len):?10.5mm*14.9mm
Weight(g):1.7g
No.of Cells(Lipo):1S only
Flight Controller
(Flysky SPI RX version)DiamondF4 FS FC Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Onboard 4-in-1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_50_REV16_8.HEX
Default protocol: DSHOT600
Onboard Flysky SPI receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
Onboard 5.8GHz VTX
Output power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels(include Race band)
Smart audio ready
Runcam Nano3
Model: RunCam Nano 3
Image Sensor: 1/3? CMOS
Horizontal Resolution: 800TVL
Lens : 2.3mm(M6.5) FOV 140°
Signal System: PAL/NTSC Non-Switchable
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm
Lipo Battery
Capacity:650mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 60mmx18mmx8mm
Weight: 16g
Connector: PH2.0
Includes
1 x 75mm Frame (Mobula7 frame)
1 x Option2: DiamondF4 FS built-in SPI Flysky receiver
4 x EX0802 KV19000 Unibell brushless motor
1 x HQPROP 40MMX2 propeller(4cw+4ccw)
1 x Runcam Nano3
1 x Built-in 5.8G 40ch 25mw-200mw VTX
2 x 1s 650mah Lipo battery
1 x Propeller disassemble tool
1 x Screwdriver
1 x Happymodel Carry case
There are currently no product reviews.
Write Review
There are currently no videos