iFlight Cidora SL5-E 6S FPV Drone - BNF XM+

Write Review
Additional Information
  • Weight : 1.20
  • Model : IB07590
Qty :
Cidora SL5-E 6S FPV Drone - BNF with our best iFlight components installed and pre-tuned! SL5 is a 5" size BNF (Bind-and-Fly) quadcopter that comes fully built with everything you need to liftoff!

- Full 3K Carbon Fiber airframe
- Easy arm swaps -215mm wheelbase?115g
- Popular Squish X configuration
- SucceX-E F4 with 45A 4in1 ESC stack

- Total Dimensions: 165*138mm (body dimension)
- Frame Wheelbase: 215mm
- SucceX-E F4 Flight controller
- SucceX-E 45A 2-6s 4-in-1 ESC Dshot600
- XING-E 2207 1800KV (6S)
- Caddx.us Ratel 2.1mm FPV cam
- Nazgul 5140 propellers grey
- Weight: 384.2 (without GoPro TPU mount)

SucceX-E F4 Flight controller Specification:
- MCU?STM32F405
- IMU?MPU6000
- Betaflight OSD?YES
- Blackbox?8MB
- 4X Uarts?1 2 3 6 )
- 8 x Dshot/Proshot/Oneshot output
- 8 x individual ESC power/ signal pads
- 1 x Group of Gnd/Vbat/M1/M2/M3/M4/Cur/TX
- VTX protocol?YES?IRC Tramp?
- WS2812 led Strip?YES
- Baro?No
- Beeper?YES
- Input?2-6S?Max 8S?
- BEC?5V/2.5A cont
- Firmware :betaflight_4.0.5_BETAFLIGHTF4.hex

- Mounting?30.5*30.5mm??4mm with Grommets ?3mm
- Dimensions?36*36mm
- Weight?7.6g

SucceX-E 45A 4in1 ESC Specification:
- Dimension: 40*43mm
- Mounting Holes: 30.5*30.5mm/?3mm
- Weight:14.4g
- Supports 2-6S Lipo input
- STM32F051 MCU, 48Mhz Runs BLHELI 32.X Firmware
- Current sensor: YES
- Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
- Target: G-H-30 BLS 16.7
BLHeliSuite download:

SucceX-Force 5.8g 25mW/100mW/400mW/800mW adjustable VTX
- Input voltage: 5V
- Channel: 48
- Power transmission: 0mW(Pit mode) / 25mW/100mW/400mW/800mW

- Support OSD Frequency and Power tuning;
- The output power is stable, the far transmission distance: ?10km
- Transmit power 5 gear switch: 25mW/200mW/400mW/800mW;
- Output 48 frequency points, and has 6 group 8 race frequency at the same time using each other without interference;
- Frequency lock fast, the boot does not interfere with companions;
- Built-in output power self-check function;
- Full format video format: NTSC /PAL;
- Wide input voltage range. low power consumption: 7V?28V +12V/500mA@800mW;
- Small size: 36mm×36mm×8mm;
- Mounting holes 4-M3
- Lightweight: ?11g(excluding antenna)
- Caddx.us Ratel 2.1mm lens FPV cam

Reflashed your drone but didn't backup the setup? Messed up the whole tune and want our factory tune back?
No need to worry! All Factory Dumps and Wiring Diagrams can be found on our Google Drive: LINK

Recommend Parts (Not included):
-TPU 3D Printed Camera Mount for Gopro Hero 5/6/7 with ND8 Filter
-TPU 3D Printed Camera Mount for GoPro Session

Package Included:
-1x Cidora SL5-E 6S FPV Drone - BNF
-2 sets Nazgul 5140 propellers

NOTE: The Hero 7 camera and TPU print camera mount are not included.

There are currently no product reviews.

Write Review

There are currently no videos

We Accept